Heat Pump Ratings in Canada: SEER2, HSPF2, COP at Low Temperatures, and What Actually Predicts Winter Performance
Which Number to Read First, Which to Read Last, and How to Compare Two Quotes Honestly
By
Published: November 18, 2026
Fact-checked · , including Natural Resources Canada, Government of Canada & ENERGY STAR
Credit: Shutterstock
Key Takeaways
•For a Canadian winter, read heating capacity and COP at -8.3°C and -15°C first, HSPF2 in Region V second, and SEER2 last.
•An HSPF2 copied from a U.S. spec sheet is usually a Region IV number. The Canadian Region V figure for the same unit is roughly 20 per cent lower.
•The AHRI reference number is the one field that makes two quotes comparable, because ratings belong to a matched system, not to an outdoor unit.
Most heat pump quotes lead with SEER2. It's the biggest number on the page, the one the brochure highlights, and the one a salesperson can say quickly. It is also a cooling rating. In most of Canada you'll spend far more money heating your house in January than cooling it in July, so the headline number on many quotes describes the season that matters least.
You probably think you're comparing efficiency. What you're actually comparing is how each unit behaves at different temperatures, and the ratings were never designed to give you that in one figure. SEER2 is a summer average. HSPF2 is a winter average weighted to a particular climate, which may not be yours. COP is a snapshot at a single temperature. Capacity, the number most homeowners never ask about, decides whether the house stays warm when it's -20°C outside.
This guide puts the ratings in order. It covers what each one measures, where it was tested, the Region IV versus Region V trap behind many confusing quotes, and the low-temperature numbers that predict January. It finishes with a table showing which rating to prioritize where you live, and a short worksheet for putting two quotes side by side.
Why the Number on the Quote Is Usually the Wrong One for a Canadian Winter
Ratings answer different questions
Every rating on a spec sheet answers a narrow question under fixed lab conditions. SEER2 asks how efficiently the unit removes heat over a cooling season. HSPF2 asks how efficiently it heats over a modelled heating season. COP asks how much heat it delivers for each unit of electricity at one specific outdoor temperature. Rated capacity asks how much heat it can actually produce at that temperature.
None of these is wrong. The mistake is choosing equipment by whichever number is largest on the page.
A Canadian heat pump succeeds or fails at the cold end of the temperature range. That's where capacity drops, efficiency drops with it, and backup heat starts to take over. A unit with an impressive SEER2 can still run out of capacity at -15°C. That doesn't show up in July. It shows up in a cold house in February.
What Canada's own selection method keys on
The clearest sign of what matters is how Canadian agencies select and fund equipment. The Air-source Heat Pump Sizing and Selection Guide from Natural Resources Canada chooses equipment by heating output at 17°F (-8.3°C) or at the location's design temperature, depending on how much of the heating load the heat pump is meant to carry. It does not select by SEER2. For homes sized to carry the full winter load, the guide states that a cold-climate unit will be required in most Canadian climate zones.
Utility money points the same way. Quebec's provincial utility pays its LogisVert heat pump grant per 1,000 BTU/h of capacity at -8°C, with a higher rate for units classified as cold climate (program terms as of November 2026). When a funder pays by capacity at -8°C, it's telling you which number it thinks predicts performance.
That's the framework for the rest of this guide:
First: heating capacity and COP at -8.3°C and -15°C, plus the lowest temperature the manufacturer publishes data for.
Second: HSPF2, but only the Region V figure.
Third: SEER2 and EER2, which mostly matter for summer comfort and cooling cost.
That order isn't a value judgment against cooling. It reflects where a Canadian heating bill, and a Canadian comfort complaint, actually comes from.
The Rating Map: What Each Number Measures and Where It Was Tested
One table, every rating
Since January 1, 2023, residential heat pump ratings have been expressed as SEER2, EER2 and HSPF2 under a revised test procedure. According to AHRI's summary of the 2023 standards, the new test raises the external static pressure used in testing by up to five times to better reflect real ductwork, so the new numbers are lower than the old ones for the same equipment. A pre-2023 "16 SEER" brochure and a current "15.2 SEER2" quote can describe similar machines.
Here's what each rating does and doesn't tell you.
5 rows · 5 columnsTap a header to sort
SEER2
Seasonal cooling efficiency (Btu removed per watt-hour)
A modelled cooling season, anchored at 95°F (35°C) and milder points
Summer operating cost
Anything about winter
EER2
Cooling efficiency at a single hot condition
Steady operation at 95°F (35°C)
Peak-day cooling performance
Seasonal cooling or any heating
HSPF2
Seasonal heating efficiency (Btu delivered per watt-hour)
A modelled heating season weighted to a climate region (IV in the U.S., V in Canada)
Broad winter running cost, if the region matches your climate
How the unit behaves at -15°C or colder
COP
Instantaneous heating efficiency (heat out ÷ electricity in)
One outdoor temperature: 47°F (8.3°C), 17°F (-8.3°C), 5°F (-15°C) or lower
Cost per unit of heat on cold days
Whether there's enough heat
Rated / maximum capacity
Heat output in Btu/h
Same temperature points as COP
Whether the unit can carry your house's load, and where backup takes over
Efficiency
Read the last two columns twice. Every rating leaves something out, and the gaps line up with the questions Canadian homeowners care about most.
The legal floor in Canada
Canada sets minimums under Amendment 17 to the Energy Efficiency Regulations, published in the Canada Gazette as SOR/2022-265, and they apply to central heat pumps manufactured on or after January 1, 2023.
Central heat pump type
Minimum SEER2
Minimum HSPF2(Region V)
Split system (standard)
14.3
6.0
Single package
13.4
5.4
Small-duct high-velocity
12.0
4.9
Space-constrained
11.9
5.0
These floors are useful mainly as a reference point. A quote that lands near them is a minimum-compliance unit. That's legal, but it's rarely what you want for a primary heating system in a cold climate.
The legal minimums are also silent on low-temperature performance. The data Canadian dealers must report for a heat pump covers SEER2, cooling capacity, Region V HSPF2 and heating capacity at 8.3°C (47°F). Nothing mandatory covers -8.3°C or -15°C. If you want those numbers, and you should, you have to ask for them.
If you want the cooling side of this explained in more depth, our hub on SEER ratings for Canadian homes covers SEER2 and EER2 in detail.
One table, every rating
Since January 1, 2023, residential heat pump ratings have been expressed as SEER2, EER2 and HSPF2 under a revised test procedure. According to AHRI's summary of the 2023 standards, the new test raises the external static pressure used in testing by up to five times to better reflect real ductwork, so the new numbers are lower than the old ones for the same equipment. A pre-2023 "16 SEER" brochure and a current "15.2 SEER2" quote can describe similar machines.
Here's what each rating does and doesn't tell you.
5 rows · 5 columnsTap a header to sort
SEER2
Seasonal cooling efficiency (Btu removed per watt-hour)
A modelled cooling season, anchored at 95°F (35°C) and milder points
Summer operating cost
Anything about winter
EER2
Cooling efficiency at a single hot condition
Steady operation at 95°F (35°C)
Peak-day cooling performance
Seasonal cooling or any heating
HSPF2
Seasonal heating efficiency (Btu delivered per watt-hour)
A modelled heating season weighted to a climate region (IV in the U.S., V in Canada)
Broad winter running cost, if the region matches your climate
How the unit behaves at -15°C or colder
COP
Instantaneous heating efficiency (heat out ÷ electricity in)
One outdoor temperature: 47°F (8.3°C), 17°F (-8.3°C), 5°F (-15°C) or lower
Cost per unit of heat on cold days
Whether there's enough heat
Rated / maximum capacity
Heat output in Btu/h
Same temperature points as COP
Whether the unit can carry your house's load, and where backup takes over
Efficiency
Read the last two columns twice. Every rating leaves something out, and the gaps line up with the questions Canadian homeowners care about most.
The legal floor in Canada
Canada sets minimums under Amendment 17 to the Energy Efficiency Regulations, published in the Canada Gazette as SOR/2022-265, and they apply to central heat pumps manufactured on or after January 1, 2023.
Central heat pump type
Minimum SEER2
Minimum HSPF2(Region V)
Split system (standard)
14.3
6.0
Single package
13.4
5.4
Small-duct high-velocity
12.0
4.9
Space-constrained
11.9
5.0
These floors are useful mainly as a reference point. A quote that lands near them is a minimum-compliance unit. That's legal, but it's rarely what you want for a primary heating system in a cold climate.
The legal minimums are also silent on low-temperature performance. The data Canadian dealers must report for a heat pump covers SEER2, cooling capacity, Region V HSPF2 and heating capacity at 8.3°C (47°F). Nothing mandatory covers -8.3°C or -15°C. If you want those numbers, and you should, you have to ask for them.
If you want the cooling side of this explained in more depth, our hub on SEER ratings for Canadian homes covers SEER2 and EER2 in detail.
HSPF2 is a seasonal average, and a seasonal average depends on which season you model. The U.S. test weights hours to Climate Region IV. Canada evaluates compliance on Climate Region V, which gives more weight to cold hours, so the same machine scores lower.
Natural Resources Canada's central heat pump bulletin sets the two scales side by side. A standard split-system heat pump must reach HSPF2 7.5 in the U.S. and 6.0 in Canada, and that's the same performance level expressed two ways. Single-package units are 6.7 versus 5.4, and space-constrained units 6.3 versus 5.0. The Canadian number runs about 20 per cent lower throughout.
You can see the gap on a real listing. One single-zone wall unit on the NEEP cold-climate heat pump list carries HSPF2 9.0 in Region IV and 7.2 in Region V. Same compressor, same coil, same test. The only difference is the climate weighting.
Why this matters on a quote
The trap works in two directions.
First, an installer or a U.S. manufacturer page quotes a Region IV number to a Canadian buyer. The unit looks about 20 per cent more efficient than it will be rated in Canada. Manufacturer pages on Canadian web addresses still cite the U.S. 7.5 HSPF2 minimum without mentioning that the Canadian floor is expressed as 6.0.
Second, a homeowner compares a Region IV number on one quote with a Region V number on another. The unit with the honestly labelled Canadian rating looks worse, even when it's better.
Same unit, two numbers
HSPF2 is a seasonal average, and a seasonal average depends on which season you model. The U.S. test weights hours to Climate Region IV. Canada evaluates compliance on Climate Region V, which gives more weight to cold hours, so the same machine scores lower.
Natural Resources Canada's central heat pump bulletin sets the two scales side by side. A standard split-system heat pump must reach HSPF2 7.5 in the U.S. and 6.0 in Canada, and that's the same performance level expressed two ways. Single-package units are 6.7 versus 5.4, and space-constrained units 6.3 versus 5.0. The Canadian number runs about 20 per cent lower throughout.
You can see the gap on a real listing. One single-zone wall unit on the NEEP cold-climate heat pump list carries HSPF2 9.0 in Region IV and 7.2 in Region V. Same compressor, same coil, same test. The only difference is the climate weighting.
Why this matters on a quote
The trap works in two directions.
First, an installer or a U.S. manufacturer page quotes a Region IV number to a Canadian buyer. The unit looks about 20 per cent more efficient than it will be rated in Canada. Manufacturer pages on Canadian web addresses still cite the U.S. 7.5 HSPF2 minimum without mentioning that the Canadian floor is expressed as 6.0.
Second, a homeowner compares a Region IV number on one quote with a Region V number on another. The unit with the honestly labelled Canadian rating looks worse, even when it's better.
Important
Never compare two HSPF2 numbers until you know both are Region V. If a quote or spec sheet doesn't say, assume it's the U.S. Region IV figure and ask for the Canadian rating, or look it up yourself before deciding.
The fix is simple. Environment and Climate Change Canada points homeowners and contractors to Natural Resources Canada's energy efficiency ratings search, which lists the Region V HSPF2 for every regulated single-phase air-source heat pump in Canada. Look up the outdoor model number and the Canadian number is there.
Low-Temperature COP and Capacity: The Numbers That Predict January
Why the seasonal number falls short
HSPF2 was never designed to describe a Canadian cold snap. The Northeast Energy Efficiency Partnerships (NEEP), a non-profit whose cold-climate list Canadian programs rely on, created its specification because the seasonal heating metric has no test points below 17°F, assumes electric resistance backup, and tests in steady-state operation. A rating with no data below -8.3°C can't tell you what happens at -20°C.
Two other numbers can: COP and capacity, both measured at specific cold temperatures.
COP: efficiency at one temperature
COP is the simplest rating to understand. A COP of 3 means the heat pump delivers three units of heat for every unit of electricity it uses. Electric baseboard heat has a COP of 1.
COP falls as the outdoor air gets colder, because there's less heat to collect and the compressor works harder to move it. Natural Resources Canada's heat pump guide puts typical air-source COP at 2.0 to 5.4 at 8°C, falling to 1.1 to 3.7 at -8°C. Notice how much wider the spread gets. In mild weather most units are respectable. In real cold, some barely beat a baseboard heater and others still deliver more than three times their input.
The cold end is where products differ. It's also the end most quotes leave out.
Field data confirms the shape. A cold-climate unit tested by federal researchers at the Canadian Centre for Housing Technology in Ottawa averaged a COP of about 3.0 at +4.9°C and about 1.5 at -21.1°C. That was 2013 equipment, so current units should do better, but the curve is the same: efficiency roughly halves across an ordinary Ottawa winter.
Capacity: whether there's enough heat
Efficiency tells you what the heat costs. Capacity tells you whether you get enough of it.
Most air-source heat pumps deliver less heat as it gets colder, at exactly the moment the house loses more heat. The outdoor temperature where those two lines cross is the balance point. Below it, the heat pump can't keep up on its own and backup heat makes up the difference. A unit that holds its capacity in the cold pushes the balance point down and leaves less of the winter to the backup.
The NEEP record above shows how much spread hides inside one product:
Outdoor temperature
Rated capacity(Btu/h)
Maximum capacity(Btu/h)
COP at maximum
47°F (8.3°C)
12,000
23,000
2.87
17°F (-8.3°C)
8,000
15,500
2.02
5°F (-15°C)
8,400
13,070
1.77
The "rated" column is what most brochures show. The "maximum" column is what the variable-speed compressor can deliver when the house actually needs it. For a Canadian buyer, maximum capacity at -15°C is the more useful figure, and here it's 108 per cent of the rated 8.3°C capacity, a ratio NEEP calls capacity maintenance.
The thresholds worth knowing
Three organizations publish cold-climate thresholds, and they line up closely.
NEEP's current specification, version 4.0 (effective January 1, 2023), requires a COP of at least 1.75 at 5°F at maximum capacity, plus a variable-capacity compressor. It also asks manufacturers to report performance at their lowest catalogued temperature. The ENERGY STAR Cold Climate designation uses the same 1.75 COP at 5°F, adds a requirement that capacity at 5°F be at least 70 per cent of capacity at 47°F, and requires a check that the unit hits those numbers on its own built-in controls, as it would in a home.
The Canadian version, expressed in Celsius and Region V terms, appears in Efficiency Manitoba's selection guidance: a cold-climate unit should have an HSPF2 (Region V) of at least 6.6, a COP of at least 1.8 at -15°C, a SEER2 of at least 15.2, and capacity maintenance of at least 70 per cent, measured as maximum output at -15°C divided by rated output at 8.3°C.
Why the seasonal number falls short
HSPF2 was never designed to describe a Canadian cold snap. The Northeast Energy Efficiency Partnerships (NEEP), a non-profit whose cold-climate list Canadian programs rely on, created its specification because the seasonal heating metric has no test points below 17°F, assumes electric resistance backup, and tests in steady-state operation. A rating with no data below -8.3°C can't tell you what happens at -20°C.
Two other numbers can: COP and capacity, both measured at specific cold temperatures.
COP: efficiency at one temperature
COP is the simplest rating to understand. A COP of 3 means the heat pump delivers three units of heat for every unit of electricity it uses. Electric baseboard heat has a COP of 1.
COP falls as the outdoor air gets colder, because there's less heat to collect and the compressor works harder to move it. Natural Resources Canada's heat pump guide puts typical air-source COP at 2.0 to 5.4 at 8°C, falling to 1.1 to 3.7 at -8°C. Notice how much wider the spread gets. In mild weather most units are respectable. In real cold, some barely beat a baseboard heater and others still deliver more than three times their input.
The cold end is where products differ. It's also the end most quotes leave out.
Field data confirms the shape. A cold-climate unit tested by federal researchers at the Canadian Centre for Housing Technology in Ottawa averaged a COP of about 3.0 at +4.9°C and about 1.5 at -21.1°C. That was 2013 equipment, so current units should do better, but the curve is the same: efficiency roughly halves across an ordinary Ottawa winter.
Capacity: whether there's enough heat
Efficiency tells you what the heat costs. Capacity tells you whether you get enough of it.
Most air-source heat pumps deliver less heat as it gets colder, at exactly the moment the house loses more heat. The outdoor temperature where those two lines cross is the balance point. Below it, the heat pump can't keep up on its own and backup heat makes up the difference. A unit that holds its capacity in the cold pushes the balance point down and leaves less of the winter to the backup.
The NEEP record above shows how much spread hides inside one product:
Outdoor temperature
Rated capacity(Btu/h)
Maximum capacity(Btu/h)
COP at maximum
47°F (8.3°C)
12,000
23,000
2.87
17°F (-8.3°C)
8,000
15,500
2.02
5°F (-15°C)
8,400
13,070
1.77
The "rated" column is what most brochures show. The "maximum" column is what the variable-speed compressor can deliver when the house actually needs it. For a Canadian buyer, maximum capacity at -15°C is the more useful figure, and here it's 108 per cent of the rated 8.3°C capacity, a ratio NEEP calls capacity maintenance.
The thresholds worth knowing
Three organizations publish cold-climate thresholds, and they line up closely.
NEEP's current specification, version 4.0 (effective January 1, 2023), requires a COP of at least 1.75 at 5°F at maximum capacity, plus a variable-capacity compressor. It also asks manufacturers to report performance at their lowest catalogued temperature. The ENERGY STAR Cold Climate designation uses the same 1.75 COP at 5°F, adds a requirement that capacity at 5°F be at least 70 per cent of capacity at 47°F, and requires a check that the unit hits those numbers on its own built-in controls, as it would in a home.
The Canadian version, expressed in Celsius and Region V terms, appears in Efficiency Manitoba's selection guidance: a cold-climate unit should have an HSPF2 (Region V) of at least 6.6, a COP of at least 1.8 at -15°C, a SEER2 of at least 15.2, and capacity maintenance of at least 70 per cent, measured as maximum output at -15°C divided by rated output at 8.3°C.
Note
The U.S. threshold of 1.75 at 5°F and the Canadian figure of 1.8 at -15°C describe the same test point. The NEEP unit above, at 1.77, falls between them. Program eligibility is decided by each program's own list, so check the list rather than doing the rounding yourself.
The ENERGY STAR and NEEP HSPF2 floors (8.1 to 8.5 for cold-climate splits) are U.S. Region IV numbers. Don't hold a Canadian Region V figure to them.
A split-system heat pump is at least two pieces: an outdoor unit, and an indoor coil or air handler, often paired with a furnace. Its ratings describe that specific combination, tested together. Swap the indoor coil and you change the system, even if the outdoor unit is identical.
That's why the AHRI reference number matters. Each certified combination gets one number tied to specific outdoor, indoor and, where applicable, furnace model numbers. Natural Resources Canada's product list tells homeowners to ask the contractor to put the AHRI number and every model number in the quote, so the system can be checked against the eligible list. The same number now identifies equipment on the federal rebate's product list and on Quebec and Ontario program paperwork.
A quote with an outdoor model number and no AHRI number can't be verified. Two quotes without AHRI numbers can't be honestly compared.
"Certified" and "rated in accordance with" are different claims
Spec sheets use two phrases that sound alike. "AHRI Certified" means the ratings were independently verified. "Rated in accordance with AHRI Standard 210/240" means the manufacturer followed the test method, nothing more. The AHRI Brand Usage Guide is explicit: the second phrase does not mean the ratings were independently tested and certified. Only products submitted for annual independent testing, with their claims verified, can carry the AHRI Certified mark and appear in the AHRI Directory.
What to pull from each document
Here's how the paperwork divides up:
The AHRI certificate gives the matched system's certified SEER2, EER2 and HSPF2 (check the region), plus rated heating capacity at 47°F and 17°F.
The NEEP record or manufacturer extended performance table gives minimum, rated and maximum capacity and COP at 47°F, 17°F, 5°F and the lowest catalogued temperature. This is where the January numbers live.
The manufacturer's installation manual gives the minimum operating temperature. Natural Resources Canada says newer models typically cut out somewhere between -15°C and -25°C.
Natural Resources Canada's ratings search gives the Canadian Region V HSPF2 when a U.S. sheet only shows Region IV.
Tip
When you ask for quotes, ask each contractor for the AHRI reference number and a copy of the extended heating performance table for the exact system they're proposing. A contractor who can't produce either has given you a price, not a specification.
The ratings don't change across the country. Their importance does, and the reason is how much of the heating load arrives in cold weather.
The Natural Resources Canada sizing guide's climate table shows the spread. In a marine climate, 83 per cent of the season's heating load occurs above +2°C and 99.5 per cent above -9°C. In a cold, humid climate only 27.5 per cent occurs above +2°C and 77.5 per cent above -9°C. In a very cold climate, roughly a third of the load arrives below -9°C, and in subarctic conditions more than half does.
Put simply, coastal BC heats mostly in mild weather, so a seasonal average describes it well. Northern Ontario heats a large share of the time in deep cold, where a seasonal average hides what matters.
Design temperatures show the same thing. That's the January temperature colder than which only about 19 hours fall in an average year. Vancouver's is -6°C under the Vancouver Building By-law's climatic data.
Ontario's values come from the provincial Supplementary Standard SB-1: -16°C in Windsor, -18°C in Toronto and London, -31°C in Thunder Bay, and -34°C in Timmins and Kapuskasing. The Prairies and northern Quebec sit at the cold end of that range.
The worth-it-when table
The table below matches the climate categories in the sizing guide to Canadian regions roughly, and pairs each with a backup-heat setup. "Capacity at -8.3°C" means maximum heating output at 17°F. "Capacity maintenance" means maximum output at -15°C divided by rated output at 8.3°C.
5 rows · 4 columnsTap a header to sort
Coastal BC (design temperature around -6°C), any backup
HSPF2 (Region V), then SEER2
Region V HSPF2 comfortably above the 6.0 floor; capacity at -8.3°C that covers your load
Nearly all heating happens above -9°C, so a seasonal average describes your winter well
Southern Ontario (about -16°C to -18°C) with a gas furnace as backup
Capacity and COP at -8.3°C, then the changeover temperature
Output at -8.3°C close to the house's load at that temperature (Natural Resources Canada's heating-emphasis method)
The furnace covers the coldest hours; how much of the winter the heat pump carries depends on its output at -8.3°C
Southern Ontario, all-electric or electric-resistance backup
Maximum capacity at the design temperature and COP at -15°C
COP of 1.8 or higher at -15°C, capacity maintenance of 70 per cent or more
Every hour below the balance point is billed at resistance-heat rates
Prairies, northern Ontario or northern Quebec, with backup
Lowest catalogued temperature data and minimum operating temperature
COP of 1.8 or higher at -15°C, capacity maintenance of 70 per cent or more, published data well below -15°C
A large share of the load arrives below -9°C; a unit that stops at -15°C leaves those hours to the backup
Prairies or far north, no backup planned
Maximum capacity at your design temperature, from extended data
Output greater than the design heating load at the design temperature (Natural Resources Canada's no-backup method)
Natural Resources Canada says a cold-climate unit will be needed in most Canadian zones, and anything short of design-temperature capacity means a cold house
Backup heat changes the answer
If you keep a gas or oil furnace, the changeover setting decides how much of the winter the heat pump actually runs. NEEP's cold-climate installation guide recommends an outdoor cutout that locks out central backup heat above a set point, typically between 20°F and 35°F (about -7°C to +2°C), adjusted for comfort. Set the changeover too high and an excellent low-temperature unit spends most of January idle while the furnace runs.
A quick illustration of the Natural Resources Canada method shows why capacity at -8.3°C matters. The guide's formula for the target capacity at 17°F is the design heating load multiplied by 43, divided by 60 minus the design temperature in Fahrenheit. For a Toronto house with a design heating load of 40,000 Btu/h at about 0°F (-18°C), that works out to roughly 28,700 Btu/h at -8.3°C. That's the number to check on the extended table, not SEER2.
The ratings don't change across the country. Their importance does, and the reason is how much of the heating load arrives in cold weather.
The Natural Resources Canada sizing guide's climate table shows the spread. In a marine climate, 83 per cent of the season's heating load occurs above +2°C and 99.5 per cent above -9°C. In a cold, humid climate only 27.5 per cent occurs above +2°C and 77.5 per cent above -9°C. In a very cold climate, roughly a third of the load arrives below -9°C, and in subarctic conditions more than half does.
Put simply, coastal BC heats mostly in mild weather, so a seasonal average describes it well. Northern Ontario heats a large share of the time in deep cold, where a seasonal average hides what matters.
Design temperatures show the same thing. That's the January temperature colder than which only about 19 hours fall in an average year. Vancouver's is -6°C under the Vancouver Building By-law's climatic data.
Ontario's values come from the provincial Supplementary Standard SB-1: -16°C in Windsor, -18°C in Toronto and London, -31°C in Thunder Bay, and -34°C in Timmins and Kapuskasing. The Prairies and northern Quebec sit at the cold end of that range.
The worth-it-when table
The table below matches the climate categories in the sizing guide to Canadian regions roughly, and pairs each with a backup-heat setup. "Capacity at -8.3°C" means maximum heating output at 17°F. "Capacity maintenance" means maximum output at -15°C divided by rated output at 8.3°C.
5 rows · 4 columnsTap a header to sort
Coastal BC (design temperature around -6°C), any backup
HSPF2 (Region V), then SEER2
Region V HSPF2 comfortably above the 6.0 floor; capacity at -8.3°C that covers your load
Nearly all heating happens above -9°C, so a seasonal average describes your winter well
Southern Ontario (about -16°C to -18°C) with a gas furnace as backup
Capacity and COP at -8.3°C, then the changeover temperature
Output at -8.3°C close to the house's load at that temperature (Natural Resources Canada's heating-emphasis method)
The furnace covers the coldest hours; how much of the winter the heat pump carries depends on its output at -8.3°C
Southern Ontario, all-electric or electric-resistance backup
Maximum capacity at the design temperature and COP at -15°C
COP of 1.8 or higher at -15°C, capacity maintenance of 70 per cent or more
Every hour below the balance point is billed at resistance-heat rates
Prairies, northern Ontario or northern Quebec, with backup
Lowest catalogued temperature data and minimum operating temperature
COP of 1.8 or higher at -15°C, capacity maintenance of 70 per cent or more, published data well below -15°C
A large share of the load arrives below -9°C; a unit that stops at -15°C leaves those hours to the backup
Prairies or far north, no backup planned
Maximum capacity at your design temperature, from extended data
Output greater than the design heating load at the design temperature (Natural Resources Canada's no-backup method)
Natural Resources Canada says a cold-climate unit will be needed in most Canadian zones, and anything short of design-temperature capacity means a cold house
Backup heat changes the answer
If you keep a gas or oil furnace, the changeover setting decides how much of the winter the heat pump actually runs. NEEP's cold-climate installation guide recommends an outdoor cutout that locks out central backup heat above a set point, typically between 20°F and 35°F (about -7°C to +2°C), adjusted for comfort. Set the changeover too high and an excellent low-temperature unit spends most of January idle while the furnace runs.
A quick illustration of the Natural Resources Canada method shows why capacity at -8.3°C matters. The guide's formula for the target capacity at 17°F is the design heating load multiplied by 43, divided by 60 minus the design temperature in Fahrenheit. For a Toronto house with a design heating load of 40,000 Btu/h at about 0°F (-18°C), that works out to roughly 28,700 Btu/h at -8.3°C. That's the number to check on the extended table, not SEER2.
Two heat pump quotes rarely use the same format. The worksheet below makes them comparable. Fill in both columns, and treat every blank as a question to send back to the contractor before you sign.
13 rows · 4 columnsTap a header to sort
AHRI reference number
Quote or AHRI certificate
Outdoor, indoor and furnace model numbers
Quote
"AHRI Certified" (not just "rated in accordance with")
Certificate or AHRI Directory
HSPF2, Region V
Natural Resources Canada ratings search or Canadian listing
SEER2
AHRI certificate
Maximum heating capacity at -8.3°C (17°F)
Extended performance table or NEEP record
Maximum capacity and COP at -15°C (5°F)
Extended performance table or NEEP record
Lowest catalogued temperature, and output there
Extended performance table or NEEP record
Minimum operating temperature
Installation manual
Load calculation used (for example, CSA F280) and design temperature
Contractor
Backup heat type and changeover temperature
Contractor
On the eligible list for your rebate program
Program list, checked by AHRI number
Commissioning steps included
Quote
The rows people skip
Three rows decide more than the rest.
Load calculation. A capacity figure means nothing until you know the load it has to meet. A contractor who sized the system from the old furnace's nameplate hasn't measured your house. The BC installer best-practice guide points to CSA F280 as the recommended method for heating and cooling loads and warns that oversizing causes excessive cycling, shorter equipment life, lower efficiency and poor summer dehumidification. The goal is enough capacity at the cold end, not the biggest unit on the truck.
Program eligibility. Rebate lists are keyed to the exact matched system. Ontario's Home Renovation Savings program also requires pre-approval before installation, as of November 2026. A unit that's eligible with one indoor coil may not be with another.
Commissioning. Ratings describe a correctly installed system in a lab. U.S. Department of Energy research summarized by the Pacific Northwest National Laboratory's Building America Solution Center found that 70 to 90 per cent of air conditioner and heat pump systems have at least one installation or maintenance fault that compromises performance. For dual-fuel systems, commissioning should confirm that backup heat runs only below the balance point.
Fill in the same rows for both
Two heat pump quotes rarely use the same format. The worksheet below makes them comparable. Fill in both columns, and treat every blank as a question to send back to the contractor before you sign.
13 rows · 4 columnsTap a header to sort
AHRI reference number
Quote or AHRI certificate
Outdoor, indoor and furnace model numbers
Quote
"AHRI Certified" (not just "rated in accordance with")
Certificate or AHRI Directory
HSPF2, Region V
Natural Resources Canada ratings search or Canadian listing
SEER2
AHRI certificate
Maximum heating capacity at -8.3°C (17°F)
Extended performance table or NEEP record
Maximum capacity and COP at -15°C (5°F)
Extended performance table or NEEP record
Lowest catalogued temperature, and output there
Extended performance table or NEEP record
Minimum operating temperature
Installation manual
Load calculation used (for example, CSA F280) and design temperature
Contractor
Backup heat type and changeover temperature
Contractor
On the eligible list for your rebate program
Program list, checked by AHRI number
Commissioning steps included
Quote
The rows people skip
Three rows decide more than the rest.
Load calculation. A capacity figure means nothing until you know the load it has to meet. A contractor who sized the system from the old furnace's nameplate hasn't measured your house. The BC installer best-practice guide points to CSA F280 as the recommended method for heating and cooling loads and warns that oversizing causes excessive cycling, shorter equipment life, lower efficiency and poor summer dehumidification. The goal is enough capacity at the cold end, not the biggest unit on the truck.
Program eligibility. Rebate lists are keyed to the exact matched system. Ontario's Home Renovation Savings program also requires pre-approval before installation, as of November 2026. A unit that's eligible with one indoor coil may not be with another.
Commissioning. Ratings describe a correctly installed system in a lab. U.S. Department of Energy research summarized by the Pacific Northwest National Laboratory's Building America Solution Center found that 70 to 90 per cent of air conditioner and heat pump systems have at least one installation or maintenance fault that compromises performance. For dual-fuel systems, commissioning should confirm that backup heat runs only below the balance point.
Warning
No rating survives a bad installation. Ask each contractor to put refrigerant charge verification, airflow measurement for ducted systems, and controls set-up in writing. A quote that skips them leaves you holding the risk that the unit never reaches its rated numbers.
Ryan is the founder of Homeowner.ca and a proud Canadian homeowner based in Guelph, Ontario. Over his 25-year career in digital publishing, he has focused on transforming complex information into clear, practical guidance that helps people make confident, well-informed decisions.
The legal minimum for a standard split-system heat pump is 14.3 SEER2. Cold-climate guidance generally looks for 15.2 or higher. Beyond that, extra SEER2 mostly lowers summer cooling cost, which is a small share of the annual bill in most Canadian homes.
Read only the Region V figure. The Canadian minimum for a standard split system is 6.0, and Canadian cold-climate guidance looks for 6.6 or higher. If a quote shows 8.5 or 9 without naming the region, confirm it, because that range is typical of U.S. Region IV ratings.
The quote is probably showing the U.S. Region IV rating. Canada rates the same equipment on Region V, which weights cold hours more heavily, so the Canadian number is roughly 20 per cent lower.
Cold-climate thresholds call for a COP of at least 1.75 to 1.8 at -15°C (5°F), measured at maximum capacity. Higher is better, but capacity at that temperature matters just as much.
For most of Canada, COP and capacity at -8.3°C and -15°C are better predictors than HSPF2, because the seasonal metric includes no test points below -8.3°C. Coastal BC is the main exception.
There's no exact conversion, because the 2023 test raised the external static pressure used in testing. Both new numbers come out lower for the same equipment, so compare SEER2 with SEER2 and HSPF2 with HSPF2 only.
It identifies a certified matched combination of outdoor unit, indoor coil or air handler and, where applicable, furnace. Federal and provincial rebate lists use it to confirm eligibility, and it's the only reliable way to compare two quotes.
No. A standard ENERGY STAR label is about efficiency. Look for the separate Cold Climate designation, which adds a 5°F COP and capacity test, and still check the minimum operating temperature against your local design temperature.
Natural Resources Canada. Cooling and Heating Season Performance Assessment of a Cold Climate Air Source Heat Pump at the Canadian Centre for Housing Technology. Retrieved from https://natural-resources.canada.ca/
Natural Resources Canada. Air Source Heat Pumps and Cold Climate Air Source Heat Pumps (searchable product list). Retrieved from https://spl-lpi.nrcan-rncan.gc.ca/
Government of Canada. (2022). Regulations Amending the Energy Efficiency Regulations, 2016 (Amendment 17), SOR/2022-265. Canada Gazette, Part II. Retrieved from https://gazette.gc.ca/
Environment and Climate Change Canada. (2026). Heat pump resources and tools for HVAC professionals. Retrieved from https://www.canada.ca/
Environment and Climate Change Canada. (2026). One million home energy retrofits. Retrieved from https://www.canada.ca/
Northeast Energy Efficiency Partnerships. (2023). Cold Climate Air Source Heat Pump Specification (Version 4.0). Retrieved from https://neep.org/
Northeast Energy Efficiency Partnerships. ccASHP Specification & Product List. Retrieved from https://neep.org/
Northeast Energy Efficiency Partnerships. Cold Climate Air Source Heat Pump Product List, record for AHRI 214931160. Retrieved from https://ashp.neep.org/
Northeast Energy Efficiency Partnerships. Guide to Installing Air-Source Heat Pumps in Cold Climates. Retrieved from https://neep.org/
Air-Conditioning, Heating, and Refrigeration Institute. 2023 Energy Efficiency Standards. Retrieved from https://www.ahrinet.org/
Air-Conditioning, Heating, and Refrigeration Institute. (2023). 2023 Brand Usage Guide. Retrieved from https://www.ahrinet.org/
Pacific Northwest National Laboratory, Building America Solution Center. Heat Pump Quality Installation and Commissioning. Retrieved from https://basc.pnnl.gov/
Home Performance Stakeholder Council (prepared by ICF Canada). (2019). Heat Pump Best Practices Installation Guide for Existing Homes. Retrieved from https://www.homeperformance.ca/
Ontario Ministry of Municipal Affairs and Housing. (2014). Supplementary Standard SB-1: Climatic and Seismic Data. Retrieved from https://www.hvactechgroup.com/
City of Vancouver. (2019). Vancouver Building By-law, Division B Appendix C: Climatic and Seismic Information for Building Design in Vancouver. Retrieved from https://free.bcpublications.ca/
Hydro-Québec. (2026). LogisVert Program grants for residential customers. Retrieved from https://www.hydroquebec.com/